Will It Fit My Ute?

Will LockNMat Fit My Ute?

LockNMat is a universal modular ute tray organiser and tub divider designed for many popular Australian dual-cab ute trays and tubs. Ute tray dimensions vary between models—choose your ute below to view the fitment guide for your vehicle.

Choose My Ute Model
Universal Modular Pack
Fits Popular Dual-Cab Utes
12 Blockers Included
No Drilling or Glue

Popular Models

Choose Your Ute Model.

Select your ute below to view the dedicated LockNMat fitment guide for that model. Each page explains the expected layout for that vehicle’s dual-cab tray size and how the universal modular system fits within the usable tray or tub floor area.

Ford Ranger Tray size, expected layout and fitment guidance. View Guide → Toyota HiLux Tray size, expected layout and fitment guidance. View Guide → Isuzu D-MAX Tray size, expected layout and fitment guidance. View Guide → Mitsubishi Triton Tray size, expected layout and fitment guidance. View Guide → Mazda BT-50 Tray size, expected layout and fitment guidance. View Guide → Nissan Navara Tray size, expected layout and fitment guidance. View Guide → Volkswagen Amarok Tray size, expected layout and fitment guidance. View Guide → BYD Shark 6 Tray size, expected layout and fitment guidance. View Guide → GWM Cannon Tray size, expected layout and fitment guidance. View Guide → Kia Tasman Tray size, expected layout and fitment guidance. View Guide → LDV T60 MAX Tray size, expected layout and fitment guidance. View Guide →

How to Measure

Measure Between the Wheel Arches.

The most important measurement is the usable ute tray width between the wheel arches—the main floor area LockNMat is designed to cover. Dual-cab tray size varies between models, so check your ute tray dimensions before ordering.

1
Measure the Narrowest Width Measure the clear ute tray width between the wheel arches or inner tub walls where the tiles will sit. This is the key fitment measurement.
2
Check Liners and Moulded Edges Plastic tub liners, spray liners, shaped edges and aftermarket accessories can slightly change the usable tray or tub floor space.
3
Allow for Small Side Gaps Because LockNMat layouts use whole tiles and filler pieces, a small side gap is normal on many utes—commonly around 20 mm and never more than 25 mm per side. The locking blockers connect directly to the tile pattern.
LockNMat fitted between the wheel arches showing usable ute tray width
Fit Between the Wheel Arches

Fitment Notes

What to Expect After Installation.

LockNMat is designed to be practical, modular and easy to install. It is not a custom-cut tray liner, so small variations are normal depending on your ute model, tray measurements, liner and accessories.

Between the Arches

The system is primarily designed to sit within the main usable tray or tub floor area between the wheel arches.

Small Gaps Are Normal

Because layouts use whole tiles and filler pieces, a small gap may remain after installation—commonly around 20 mm and never more than 25 mm per side. The gap stays at the tub edge, while the locking blockers connect directly to the tile pattern.

Liners Can Change Fit

Factory tubs, plastic tub liners, spray liners, moulded tray shapes and aftermarket accessories can slightly change the usable space and how the system sits.

Important Safety Note LockNMat helps organise everyday ute tray and tub loads and reduce general movement. It is not a certified load-restraint system. Heavy, sharp, dangerous or legally restrained loads must always be secured separately using suitable rated restraint equipment.

Fitment FAQ

Quick Fitment Answers.

These answers help set clear expectations before ordering. For detailed installation instructions, visit the How It Works guide.

Does LockNMat Cover the Whole Tray?

LockNMat is designed to cover the main usable tray or tub floor area between the wheel arches. Some edge areas may remain uncovered depending on your ute model, liner, moulded edges and accessories.

Is a Side Gap a Problem?

A small side gap is normal on many ute models—commonly around 20 mm and never more than 25 mm per side. The gap remains at the tub edge, while the locking blockers connect directly to the tile pattern and can still be positioned around suitable everyday gear.

Can I Install It Myself?

Yes. LockNMat is designed for simple DIY installation without drilling, glue, screws or permanent tray modification. The layout can also be removed or adjusted when required.

What If My Ute Has a Liner?

Plastic tub liners, spray liners and moulded edges can slightly change the available tray space. Measure the usable floor area inside the liner before ordering and review the fitment guide for your ute model.

What Ute Tray Measurements Do I Need?

Measure the usable width between the wheel arches and the usable tray or tub floor length. Width is the main fitment measurement, while length helps determine expected tile-row coverage and filler placement. Check your vehicle’s fitment guide for model-specific information.

Ready to Order?

Check Your Tray. Then Build Your LockNMat Setup.

Once you have measured your ute tray size between the wheel arches and reviewed the expected side-gap tolerance, order the complete LockNMat modular ute tray system.

Shop LockNMat View Setup Guide